ELECTROCHEMICAL DEBURRING PROCESS PDF

Last updated: May 15, Electrochemical Deburring: Electrochemical deburring ECD is an adaptation of Electrochemical Machining ECM process designed to remove burrs or to round sharp corners on metal workpieces by anodic dissolution method. One possible setup for ECD is shown in below figure 1. The electrode tool is designed better to focus the metal removal action on the burr. The electrolyte material flows through the hole to carry away the burr particles. Less material is removed in the Electrochemical Deburring ECD machining process; cycle times are much shorter. A typical cycle time in ECD is less than a minute.

Author:Zulull Arashihn
Country:Eritrea
Language:English (Spanish)
Genre:History
Published (Last):14 January 2007
Pages:134
PDF File Size:18.33 Mb
ePub File Size:17.43 Mb
ISBN:936-6-60843-124-9
Downloads:49341
Price:Free* [*Free Regsitration Required]
Uploader:Taulkree



Contact Us Electrochemical Deburring Systems Electrolytic Deburring, also known as Electro Chemical Deburring ECD is a highly productive, precision technology for deburring and radiusing edges, especially at the intersections of internal passages, or other difficult to access features of a workpiece. Process ECD removes metal by non-coontact, electrochemical action, with is fast, highly-selective, and safe. However, unlike plating, during electrolytic deburring the metal which is removed is converted into fine metal hydroxide particles, which are flushed out of the part by the electrolyte, and can be removed from the electrolyte with filtration.

The piece is then placed onto a fixture, and is connected to the positive side of the power supply, becoming an anode.

Electrolyte is flowed through the workpiece, while the current is turned on for 10 — 30 seconds. With multiple electrodes, multiple intersections can be simultaneously deburred. At the end of the cycle, the current is turned off, electrolyte flow stops, and the part is removed from the fixture.

The workpiece is rinsed with water, or with a rust inhibitor solution for mild steel workpieces. In a frequent application: deburring the edges of two intersecting holes, the part would be placed onto a fixture, a negatively charged electrode cathode is located into an internal passage of the workpiece.

The electrode is insulated except at its tip, which is precisely placed at the intersection of the two holes. The workpiece is connected to the positive side of the power supply and becomes an anode. Electrolyte is flowed through the workpiece and current is turned on for 10 to 30 seconds. Because of the placement of the cathode into the workpiece, the burred edges of the intersecting holes are closest to the conductive tip of the electrode; metal removal is thus focussed at these edges which are quickly deburred and radiused.

With multiple electrodes, multiple intersections in a workpiece can be simultaneously deburred. At the end of the cycle, the current is turned off, electrolyte flow stops, and the part is removed from the fixture and simply rinsed with water or with a rust inhibitor solution for mild steel workpieces. The process involves three principle elements: a fixture, the machine, and the electrolyte. Fixtures An ECD fixture starts with a base made from a conductive material onto which a workpiece is mounted and precisely located.

An electrode may be mounted stationary onto the base such that it is correctly positioned relative to the feature being deburred when the part is mounted onto the fixture, or electrodes may be mounted on pneumatically actuated slides and positioned inside the workpiece after it has been located onto the base.

Tool design centers around the mask and the electrode. Masks are made from nonconductive material and are bored out to cover the electrode except in the work zone, plus additional space for the flow of electrolyte.

The mask can also serve as a locating device for the workpiece. The gap between the electrode and the workpiece at the work zone is usually 0. Machines An ECD workstation consists of a frame mounted sink, an electrolyte tank and pumping system, and a DC power supply. A worktable to hold fixtures is mounted in the sink. Backsplashes are located at the rear and sides of the sink. Busbars for electrical current, manifolds for electrolyte, compressed air, and rinse water are mounted onto the backsplash for convenient access.

Pneumatic cylinders are frequently used both to clamp the workpiece into the fixture, establishing electrical contact, and also to index electrodes into internal workpiece features. The electrolyte tank is separated by an internal divider into two compartments for clean and dirty electrolyte sits under the frame, and has a capacity of approximately 60 gallons.

Electrolyte flow is provided by a stainless steel centrifugal pump to a manifold mounted to the frame behind the back splash; flowrates to fixtures are set by individual needle valves. Pulsed output can be provided down to 50 millisecond pulse width. Power supply cooling can be either by forced air or cooled water. All production ECD machines require an electrolyte filtration system with its own pump; bag filters, filter presses, and, for ultimate electrolyte cleanliness, nanofiltration membrane filters are used.

Electrolyte The electrolyte is a simple conductive solution of a salt dissolved in water. The most common electrolytes use sodium chloride or sodium nitrate as the salt. For most applications, we recommend an electrolyte made with 2 pounds of sodium nitrate per gallon of water. Some metals, such as titanium, require blends of several salts to achieve the best results. With good filtration, maintaining the correct salt concentration, and pH adjustment, a batch of electrolyte can be used for several months before it needs to be replaced.

Customized Solutions We can work with you to produce a controlled manufacturing solution that fits your needs, whether it is for Abrasive Flow Machining or Electrochemical Deburring. All Rights Reserved.

ENCANTARIA BRASILEIRA PDF

Electrochemical Deburring Systems

Request offer The demands made on the deburring process Workpieces with complex geometries often contain machining sectors that are difficult to get at. Undercuts, pockets or internal, intersecting drill holes do not present that much of a challenge for mechanical machining processes. However, this changes drastically when it comes to the necessary deburring, as the burrs on sections that are difficult to reach must also be removed cleanly and without negative impact on the material. The methods used up to now - mechanical or thermal processes, or water jet technology - have not achieved the intended productivity levels, nor the desired reproducibility and cost-effectiveness.

ASTM E45 PDF

Our services

Contact Us Electrochemical Deburring Systems Electrolytic Deburring, also known as Electro Chemical Deburring ECD is a highly productive, precision technology for deburring and radiusing edges, especially at the intersections of internal passages, or other difficult to access features of a workpiece. Process ECD removes metal by non-coontact, electrochemical action, with is fast, highly-selective, and safe. However, unlike plating, during electrolytic deburring the metal which is removed is converted into fine metal hydroxide particles, which are flushed out of the part by the electrolyte, and can be removed from the electrolyte with filtration. The piece is then placed onto a fixture, and is connected to the positive side of the power supply, becoming an anode. Electrolyte is flowed through the workpiece, while the current is turned on for 10 — 30 seconds. With multiple electrodes, multiple intersections can be simultaneously deburred.

2010 TOYOTA SEQUOIA OWNERS MANUAL PDF

What is Electrochemical Deburring?

.

BANCO PREGUNTAS ENAM PDF

Electrochemical Deburring and Grinding

.

Related Articles