ASTM D4585 PDF

This standard describes an accelerated aging test which allows to assess the water resistance of coatings through the use of controlled condensation. More specifically, this practice states the principles and the operating conditions that required to achieve consistent results from lab to lab. Moreover, ASTM D does not provide any indications regarding the preparation of the specimen, the specific test conditions, nor does it offer any guidance or requirements for the evaluation of the results. Click and Receive a quote within the next 4 hours.

Author:Daibei Daigami
Country:Lithuania
Language:English (Spanish)
Genre:Software
Published (Last):11 March 2004
Pages:481
PDF File Size:11.81 Mb
ePub File Size:5.46 Mb
ISBN:366-9-93932-440-4
Downloads:82503
Price:Free* [*Free Regsitration Required]
Uploader:Vudotaxe



Goltikora Link to Active This link will always route to the current Active version of the standard. Do not leave the specimens in the apparatus at the conclusion of the test as the specimens can remain wet for hours, or even days, when the apparatus is turned off.

Remove only as many specimens as can be rated within the speci? The test specimens are inclined so that condensate runs off the test surface by gravity and is replaced by fresh condensate in a continuous process during the condensate cycle.

Combining values from the two systems may result in non-conformance with the standard. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

The specimens should be mounted to avoid d between specimens that allow heat and moisture to escape. Drying periods should be at least 4 h long. The post-recovery rating allows evaluation of the permanent effects of the exposure as distinct from the transient effects, and is especially important for evaluation of color and gloss. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Alternative practices for testing water resistance of coatings include Practices DDand D Condensation is produced by exposing one surface of a coated specimen to a heated, saturated mixture of air and water vapor, while the reverse side of the specimen is exposed to the cooling effect of room temperature air. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. The specimens form the roof or walls of the test chamber so that the back sides of the specimens are exposed to the cooling effects of room temperature air.

A coating system is considered to pass if there is no evidence of water-related failure after s speci? However, it is possible to test the blister resistance of house coatings on wood specimens by mounting the uncoated wood surface facing the inside of the chamber. If the specimens cannot completely? It does not specify specimen preparation, speci? For manual drying of specimens, remove them from the apparatus. However, it is possible to test the blister resistance of house paints on wood specimens by mounting the uncoated wood surface facing the inside of the chamber.

These tests usually result in a pass or fail determination but the degree of failure also may be measured. Vents, approximately 3 to 5 mm 0. While corrosion products will drain into the water bath, they are not carried into the vapor that condenses on the test specimens.

Mount coated metal panels with the coating to be tested facing the inside of the chamber. The resulting heat transfer causes vapor to condense on the test specimens as liquid water saturated with air.

A superscript epsilon e indicates an editorial change since the last revision or reapproval. The removal of specimens for inspections during operation is permitted. Rate specimens for changes in color, blistering, etc. Cleveland Condensing Type Cabinet While corrosion products will drain into the water bath, they are not carried into the vapor that condenses on the test specimens.

Locate the chamber away from air vents and direct drafts. Other temperatures may be used provided that the temperature is reported in conformance with Section 8. Evaluate specimens no less than 5 min and no more than 10 min after removal from test, as the effects from water exposure can change within a short time. Originally approved in d Summary of Practice 3. The quality of the water in the pan does not affect the test since the evaporation and condensation process yields distilled water, but the use of tap water d result in the accumulation of residues in the water pan.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? The test is therefore useful for evaluating coatings alone or complete coating systems. Current edition approved June 1, It is the responsibility of the user of this standard to establish appropriate aetm and health practices and determine the applicability of regulatory limitations prior to use. NOTE 4—A 3 mm glass plate in place of a sample will work to monitor whether condensation is occurring.

Related Articles.

HAMA TUNGAU PDF

Popular Publishers

Goltikora Link to Active This link will always route to the current Active version of the standard. Do not leave the specimens in the apparatus at the conclusion of the test as the specimens can remain wet for hours, or even days, when the apparatus is turned off. Remove only as many specimens as can be rated within the speci? The test specimens are inclined so that condensate runs off the test surface by gravity and is replaced by fresh condensate in a continuous process during the condensate cycle.

FLUKE 741B MANUAL PDF

ASTM D4585

More D This practice is intended to induce property changes associated with end-use conditions, including the effects of sunlight, moisture, and heat. The exposure used in this practice is not intended to simulate the deterioration caused by localized weather phenomena such as atmospheric pollution, biological attack, and saltwater exposure. Therefore, no reference to the use of this practice shall be made unless accompanied by a report prepared according to Section 10 that describes the specific operating conditions used.

Related Articles